- 您现在的位置：买卖IC网 > Sheet目录1227 > MAX16031EVKIT+ (Maxim Integrated Products)KIT EVALUATION FOR MAX1603
MAX16031 Evaluation Kit
Each external temperature channel has some additional
items on the settings dialog, shown in Figure 5.
Additional fault mask bits are provided for the diode-
short and diode-open faults, and two controls are pro-
vided to set the temperature offset and gain calibration
parameters. The value provided for gain controls the
current (in μA) of the internal high-current source, while
the offset controls the digital offset value added to the
temperature conversion result (in Celsius).
Output Control Tab
The Output Control tab (Figure 6) facilitates configura-
tion of the programmable outputs.
The MAX16031 has several programmable outputs:
FAULT1, FAULT2, OVERT, RESET, GPIO1, and GPIO2.
The FAULT1 and FAULT2 outputs can be configured to
depend on many combinations of fault conditions for all
voltage, current, and temperature channels that are not
masked. The OVERT output depends on combinations
of temperature-related faults. Finally, the RESET output
depends on a combination of fault conditions for both
voltage and temperature and for a programmable set of
voltage inputs. The RESET output also has a program-
mable timeout, which is the amount of time RESET
remains asserted after all fault conditions are cleared.
GPIO1 and GPIO2 can be used as general-purpose
inputs or outputs (GPIOs), and can also be configured
to act as manual reset inputs or additional fault outputs.
When a GPIO is configured as a fault output, the follow-
ing fault conditions can be monitored:
Figure 5. Temperature Settings Dialog
?
?
?
Primary undervoltage and overvoltage for one
selectable voltage channel
One or more of the following: primary overvoltage
for all voltage inputs, secondary over/undervoltage
for all inputs, overtemperature for each sensor, or
secondary overcurrent
Both of the above options at once
6
_______________________________________________________________________________________
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
MAX16050EVKIT+
EVAL KIT FOR MAX16050
MAX16929EVKIT+
KIT EVALUATION FOR MAX16929
MAX16946EVKIT+
KIT EVALUATION FOR MAX16946
MAX17015EVKIT+
KIT EVAL FOR MAX17015
MAX17021EVKIT+
EVAL KIT FOR MAX17021
MAX1702EVKIT
EVAL KIT FOR MAX1702
MAX17710EVKIT#
RD ENERGY HARVESTING
MAX19000EVKIT+
EVAL KIT MAX19000
相关代理商/技术参数
MAX16032ETM+
功能描述:监控电路 EEPROM-Based w/NV Fault Memory RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel
MAX16032ETM+T
功能描述:监控电路 EEPROM-Based w/NV Fault Memory RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel
MAX16033LLB23+
制造商:Maxim Integrated Products 功能描述:VOLT SUPERVISOR MONITOR 2.32V 10PIN UDFN - Rail/Tube
MAX16033LLB23+T
功能描述:监控电路 Battery Backup 2.5V-Ep RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel
MAX16033LLB26+
制造商:Maxim Integrated Products 功能描述:VOLT SUPERVISOR MONITOR 2.63V 10PIN UDFN - Rail/Tube
MAX16033LLB26+T
功能描述:监控电路 Battery Backup 3.3V-Ep RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel
MAX16033LLB29+
制造商:Maxim Integrated Products 功能描述:VOLT SUPERVISOR MONITOR 2.93V 10PIN UDFN - Rail/Tube
MAX16033LLB29+T
功能描述:监控电路 Battery Backup 2.93V RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel